A Faulty Appliance
Kettles, washing machines, dishwashers, ovens and immersion heaters can develop earth leakage as their elements and seals wear. Check whether an appliance has been recalled on the Electrical Safety First product recalls page.
Emergency Electrical Service Ltd
Your RCD keeps tripping and the power will not stay on. Our electricians find exactly what is causing it and fix it properly, 24 hours a day across London.
An RCD (residual current device) is the safety switch in your consumer unit that cuts the power when electricity leaks somewhere it should not, such as through a damaged cable, a faulty appliance or a person. It reacts in a fraction of a second, which is why it saves lives.
So when your RCD trips, it is usually doing its job. The problem is finding what it is reacting to. That is where our RCD tripping electricians come in. We test each circuit and appliance until we find the fault, then repair it so the RCD stays on.
We investigate why your RCD keeps tripping.
We check circuits and appliances to locate the cause.
We work to resolve the fault and restore safe operation.
Repeated RCD trips can indicate an electrical fault that needs proper investigation. Look out for these warning signs.
The RCD trips again as soon as you reset it.
It trips at random, sometimes in the middle of the night.
It trips when it rains or after a wet spell.
It trips when you use one particular appliance, such as the kettle, oven or washing machine.
Half the house has no power and one switch in the consumer unit will not stay up.
You can smell burning or hear buzzing from the consumer unit.
An RCD can trip for several reasons. Identifying the underlying electrical fault helps restore power safely and prevent repeated trips.
Kettles, washing machines, dishwashers, ovens and immersion heaters can develop earth leakage as their elements and seals wear. Check whether an appliance has been recalled on the Electrical Safety First product recalls page.
Water entering an outdoor socket, garden light, shed supply or a light fitting affected by a leak can cause an RCD to trip, sometimes only during wet weather.
A nail or screw through a cable, rodent damage under the floor or deteriorating cable insulation can create an electrical leakage fault that causes repeated tripping.
Older split load consumer units can place several circuits on one RCD. Small amounts of normal leakage from multiple devices may accumulate until the RCD trips.
Sometimes the RCD itself is worn or faulty and trips too easily. Testing helps determine whether the protective device is responsible before anything is replaced.
Our electricians can investigate the problem and advise on the appropriate repair.
If your RCD keeps tripping, these steps may help you narrow down the cause. Never force a switch to stay on or put yourself at risk.
Unplug appliances on the affected circuits, or switch them off at the wall before attempting a reset.
STEP ONEIf there are no signs of burning, heat, smoke or other immediate danger, reset the RCD once.
STEP TWOIf the RCD stays on, reconnect appliances one at a time. If it trips again, the last item may be responsible.
STEP THREEIf the RCD trips with appliances disconnected, a fixed appliance or wiring fault may need professional testing.
STEP FOURIf your RCD keeps tripping, we follow a clear process to identify the cause, carry out the necessary repair and check that the affected circuit and RCD are working correctly.
We isolate any dangerous circuit so the rest of your home can have power back quickly.
Using an insulation resistance tester, we measure leakage on every circuit to find which one is at fault.
We narrow it down to the appliance, accessory, junction or length of cable.
We replace the faulty part, dry out and seal damp fittings, or repair the damaged cable.
We retest the circuit and RCD, show you what we found and give you a record of the work
Call our team to discuss the problem and arrange the next step.
All our electrical installation work is tested in accordance with BS 7671, the IET Wiring Regulations. We check that new electrical work meets the relevant safety requirements and provide an Electrical Installation Certificate for new circuits where applicable. For notifiable work, we also explain the relevant Building Regulations certification requirements, helping you understand the documentation provided when your installation is complete.
If your RCD keeps tripping and your electricity will not stay on, our electricians provide RCD fault finding and repair across Central London, Wimbledon, Tooting, Croydon and Norbury. Select your area to find out more about our local electrical services.
Help investigating RCD trips, earth leakage and electrical faults affecting your home or property.
Electrician in Central London →Electrical fault investigation to help identify why your RCD trips and what repair may be needed.
Electrician in Wimbledon →Support with recurring RCD trips, suspected appliance faults and electrical circuit problems.
Electrician in Tooting →Help finding the cause of an RCD that will not reset or keeps cutting power to your property.
Electrician in Croydon →RCD fault finding and repair for electrical problems affecting circuits, appliances and fittings.
Electrician in Norbury →Call our team to discuss the electrical fault and arrange the next step.
Usually a faulty appliance, water getting into a circuit or damaged wiring. If it trips with everything unplugged, the fault may be in the fixed wiring and needs an electrician to investigate and test it.
Water may be getting into something outside or near the outside of your home, such as an outdoor socket, garden light, shed supply or a leak above a ceiling light. We identify the affected circuit and determine whether the faulty fitting needs drying, sealing or replacing.
An appliance that switches on automatically could be responsible, such as a fridge compressor, freezer, immersion heater or storage heater on a timer. Our electricians test the relevant appliances and circuits to help identify the source of the earth leakage.
The RCD is a safety device that helps protect against electric shock, but the fault causing it to trip could present a shock or fire risk. Do not keep resetting it or try to bypass it. Leave the affected circuit switched off and call an electrician to investigate.
Only if testing shows that the RCD itself is faulty. In many cases, the RCD is working correctly and responding to an electrical fault elsewhere. Replacing it without finding the cause may not solve the problem.
Most RCD tripping faults are found and fixed on the first visit, but the time required depends on the cause and complexity of the fault. If a replacement part needs to be ordered, we will make the circuit safe where possible and agree the next steps with you.
Call us any time and a local electrician will be on the way.
Do not repeatedly reset or bypass a tripping RCD. Leave the affected circuit switched off and seek professional help.