
What is an RCD and why does it switch off?
A residual current device, or RCD, is a protective device designed to disconnect electricity when it detects an imbalance between current flowing out and returning through a circuit. That imbalance can indicate leakage to earth. The device is an important layer of protection against electric shock, but it does not remove the need for sound wiring, correct earthing and safe appliances.
When an RCD trips, it is not necessarily broken. In many cases it is responding to a real problem somewhere downstream. Some consumer units protect several circuits with one RCD, while other installations use individual RCBOs. The arrangement matters because one faulty item may affect several rooms even when the problem begins in a single appliance.
A single unexplained trip warrants attention, especially if it happens again. Frequent trips, a device that will not reset, or any accompanying burning smell, heat or noise should not be treated as an inconvenience to work around. The priority is to keep people safe and have the cause investigated.
Seven common reasons an RCD keeps tripping
- Faulty appliances. A washing machine, dishwasher, kettle, oven, freezer or immersion heater may develop insulation defects or moisture inside electrical components. The trip may coincide with a heating element switching on rather than with the moment the appliance is first plugged in. A qualified person can determine whether the appliance or fixed circuit is responsible.
- Water entering outdoor equipment. Garden sockets, security lighting, outdoor junction boxes and shed supplies are exposed to weather. Failed seals, damaged enclosures or poorly protected connections can allow moisture to create leakage paths. If trips cluster around rain, record the pattern and leave suspect outdoor equipment unused.
- Damaged cables. Screws, nails, rodents, building alterations and deterioration can affect cable insulation. The damage may be concealed under floors or behind finishes. Trying to locate it by opening fittings or drilling is unsafe; electrical testing and a planned inspection are needed.
- Accumulated earth leakage. Modern electronic equipment can produce small amounts of normal leakage. Where several circuits share an RCD, the combined leakage may contribute to unwanted tripping. An electrician can measure and assess the installation rather than guessing that every device is defective.
- A fixed appliance fault. Electric showers, cookers, heating controls and other permanently connected equipment may be involved. Switching off a wall switch does not necessarily isolate every conductor or make equipment safe to investigate. These items should be assessed professionally.
- Incorrect or deteriorating connections. Neutral and earth faults, moisture, or wiring changes can produce symptoms that are difficult to interpret. The position of the switch that operates does not by itself reveal the faulty connection. Testing is essential.
- A defective protective device. RCDs can fail, but replacing one before testing the circuits risks missing the real problem. A competent electrician can check device operation and decide whether replacement is justified.
Why does my RCD trip when it rains or at night?
A trip after heavy rain often points towards equipment exposed to damp conditions, but the weather pattern is a clue rather than a diagnosis. Water can travel through building fabric and affect a fitting some distance from the visible leak. A garden light or external socket is one possibility; a ceiling fitting beneath a leak is another.
Night-time tripping can occur when a timed or thermostatically controlled appliance starts. A freezer compressor, immersion heater or heating circuit may operate without anyone touching a switch. Note the approximate time and which appliances were running, but do not repeatedly operate suspect equipment to prove the theory.
Intermittent problems are especially frustrating because the circuit may appear normal when an electrician arrives. A short record of dates, weather, appliances in use and affected rooms can be valuable. Photographs of the consumer unit from a safe distance may help explain which device operated, but never remove its cover.
Safe actions while waiting for an electrician
First check for immediate danger. If you notice smoke, scorching, a burning smell, unusual heat or water around electrical equipment, stop and keep clear. Switch off only if the controls can be reached safely. A fire or immediate threat requires evacuation and a call to 999.
If there are no danger signs, identify whether the problem is limited to your home. Neighbours without power may indicate a network fault; the free 105 number helps route power-cut reports. If only your installation is affected, the cause may be inside the property.
Do not force the RCD to stay on, tape the switch in place, bypass protection or repeatedly reset it. If a particular plug-in appliance appears to be associated with a trip, stop using it. A safe, accessible plug can be disconnected with dry hands only when there are no signs of damage or overheating. Leave the affected circuit off and arrange a qualified assessment.
Keep vulnerable household members in mind. Loss of power can affect medical equipment, refrigeration, heating and lighting. If essential medical equipment is involved, follow the equipment provider’s emergency plan and seek appropriate urgent assistance rather than attempting an electrical repair yourself.
RCD tripping in flats and rented homes
In a rented home, report repeated tripping to the landlord or managing agent as soon as possible and explain any safety concerns. Avoid informal repairs or modifications. The landlord may need to arrange access for an electrician and retain appropriate records of remedial work.
In a block of flats, a supply interruption may affect only your flat, a group of flats or communal equipment. Do not assume the consumer unit in your home controls every affected circuit. Building management may need to coordinate access to common areas.
An RCD that keeps tripping is not a reliable indicator that the entire property needs rewiring. It could be a single appliance or accessory. Conversely, an installation that appears to work can still have safety defects. A professional diagnosis distinguishes these possibilities.
What different tripping patterns can reveal
An RCD that trips immediately after a reset may be responding to an existing leakage fault. One that trips only after a delay may coincide with a timer, thermostat or appliance cycle. Neither pattern proves a particular component is faulty, but the timing helps narrow the professional investigation.
A trip that affects lights and sockets together may reflect how circuits are grouped at the consumer unit. The room where power disappears is not necessarily where the fault begins. This is why a professional should identify circuit arrangements before selecting tests.
If a trip happens after a recent installation, refurbishment or leak, share that information with the electrician. A new accessory may be unrelated, but the timing can provide a useful clue. Avoid moving cables or removing fittings yourself.
How to reduce the risk of future nuisance trips
Have outdoor accessories inspected when their enclosures are damaged or seals deteriorate. Keep electrical fittings away from uncontrolled water exposure and report roof or plumbing leaks promptly. Do not attempt to waterproof a live electrical fitting with sealant or tape.
Use appliances according to their instructions and stop using items that show heat damage, cracked plugs or repeated protective-device operation. Check product recall notices from a reliable source. Regular visual awareness is useful, but it is not a substitute for electrical testing.
After a repair, ask what caused the trip and whether any other related circuits should be checked. Keep records of the work and note any future recurrence. Preventive attention is about correcting known defects, not replacing sound equipment without evidence.
Electrical help in the areas we cover
Wimbledon: RCD keeps tripping
In Wimbledon, a property may have been extended, renovated or adapted over several decades. Different generations of wiring and accessories can exist in the same building, so an electrician should assess the actual installation rather than judge safety from the age of the house alone. For local assistance, see our electrician in Wimbledon page and explain the symptoms when you contact the team.
Tooting: RCD keeps tripping
In Tooting, converted flats, family homes and rental properties may have shared building infrastructure but separate electrical installations. A problem in one flat does not automatically identify the cause or responsibility, making careful isolation and professional diagnosis important. For local assistance, see our electrician in Tooting page and explain the symptoms when you contact the team.
Croydon: RCD keeps tripping
Across Croydon, homes and flats range from older housing stock to newer developments. Electrical faults can arise in either; the condition of connections, appliances and protective devices matters more than assumptions based on a postcode. For local assistance, see our electrician in Croydon page and explain the symptoms when you contact the team.
How a professional diagnosis differs from guesswork
A reliable assessment of RCD keeps tripping begins with the symptoms and the layout of the installation. The electrician will identify the relevant circuits, inspect accessible equipment where appropriate and decide which tests are needed. The visible symptom is not always located at the source of the fault.
Electrical testing may involve continuity, insulation resistance, polarity and protective-device checks as appropriate to the circumstances. These are professional procedures that require suitable instruments, safe isolation and interpretation of the results. They are not household troubleshooting steps.
Once the underlying issue has been identified, the electrician can explain whether a component repair, replacement, additional investigation or wider installation work is appropriate. Some problems can be resolved during a visit; hidden cable damage or access restrictions may require a planned follow-up.
Following repair, the affected work should be inspected and tested as appropriate. Where certification or a record is required, keep it with the property documentation. A meaningful repair addresses the fault and verifies the result rather than merely making a warning light disappear.
If the fault recurs, record when it happens and contact the electrician again. A repeat symptom may involve a second appliance, moisture that appears only in particular conditions, or a different circuit. Do not assume that a previous repair makes a new symptom harmless.
What to tell the electrician before the visit
Explain exactly what you observed about RCD keeps tripping, including the first time it happened, whether the issue is continuous or intermittent, and whether any recent work or new equipment might be relevant. Accurate observations help the electrician plan a safe investigation without relying on guesses.
Say whether the fault affects one fitting, one room, several circuits or the entire property. If the power has failed, check from a safe place whether neighbours are affected; a wider network interruption is different from a fault inside the home. The free 105 service can direct you to the relevant network operator.
Mention burning smells, unusual heat, crackling, visible damage, water ingress, previous electric shocks or a breaker that repeatedly operates. These symptoms change the urgency of the response. Do not keep testing a suspect appliance to recreate a dangerous fault.
For a rented property, tell the landlord or managing agent promptly and share the observations in writing. For a flat, identify whether the affected equipment belongs to your dwelling or a communal area. Do not access locked or restricted electrical rooms.
Ask what checks will be carried out, whether any circuits will need to remain off, and what records will be supplied after repair or inspection. A clear explanation of the findings is more valuable than a quick reset that leaves the cause unresolved.
Useful services and next steps
Electrical faults need a response based on the condition of the installation, not a generic promise that every problem has the same solution. The following service pages explain the relevant options and can help you decide what to discuss with an electrician.
If you need urgent help, contact Emergency Electrical Service Ltd and explain the safety concern. For general independent electrical safety information, see Electrical Safety First. For a suspected wider power cut, see Power Cut 105.
Frequently asked questions
Can I keep resetting an RCD until it stays on?
No. Repeated resetting can re-energise a dangerous fault. Leave the affected circuit off and arrange professional investigation.
Does an RCD trip mean the whole house needs rewiring?
Not necessarily. A single appliance, outdoor fitting or damaged connection may be responsible. Rewiring should be recommended only after appropriate assessment.
Why does my RCD trip after rain?
Moisture in outdoor or water-affected electrical equipment is one possible cause. The affected circuit should be tested rather than guessed.
Why does the RCD trip when the washing machine heats water?
A heating element or associated component may be faulty, but a professional assessment is needed to identify the actual cause.
Can an RCD be faulty?
Yes, although it may be working correctly. An electrician can test the device and circuits before deciding on replacement.
Is an RCD the same as a circuit breaker?
No. An RCD responds to residual current imbalance; an MCB protects against overcurrent. An RCBO combines functions in one device.
Who should I call in Wimbledon or Tooting?
Contact a qualified electrician who can inspect the affected installation and carry out appropriate testing. Our local area pages explain the services available.
Final safety reminder
If there is smoke, an active fire or an immediate threat to life, leave the building, keep others away and call 999. If it is safe to reach the consumer unit without approaching heat, water, exposed conductors or damaged equipment, switch off the affected supply. Never open the consumer unit, remove socket covers, touch exposed wiring or defeat a protective device. A qualified electrician should diagnose and repair faults in fixed wiring.
Practical example: documenting an intermittent fault
Imagine the electricity cuts out on three evenings but works normally the following morning. The useful record is not simply “power failed”; it includes the date, affected rooms, which protective device operated, whether heating or cooking equipment was in use and whether there had been rain. This information can help a qualified electrician plan appropriate tests without exposing anyone to danger.
The record should not become a DIY experiment. There is no need to deliberately switch suspect appliances on or off to reproduce a fault. If a device trips again, leave the affected circuit isolated and arrange an assessment. Safety takes priority over collecting more evidence.
What a good repair explanation should include
After a professional visit, ask the electrician to explain the observed symptom, the cause supported by the tests, the work completed and any remaining limitations. Where equipment could not be accessed or further work is needed, the explanation should make that clear.
Keep any relevant certificates or records with the property paperwork. If you rent, share the information with the landlord or managing agent. A transparent explanation helps avoid repeated temporary fixes and supports informed decisions about future maintenance.
Avoiding common misconceptions
An electrical installation can work and still have a safety defect. Equally, a fault affecting one socket does not automatically mean every circuit must be replaced. Good decisions come from inspection, testing and the condition of the equipment rather than dramatic assumptions.
A protective device that trips is not necessarily the cause of the problem; it may be responding correctly to another fault. Cosmetic replacement of a fitting also does not prove the wiring behind it is sound. Appropriate professional testing connects symptoms with the actual defect.